General Plumbing / How to install a kitchen kickboard heater with Xpro Gripaloc

 

Here’s a quick article about installing a kitchen kickspace heater, including the use of Xpro Gripaloc for sealing threads:


How to Install a Kitchen Kickspace Heater

Installing a kitchen kickspace heater is a great way to add warmth to your kitchen without taking up valuable floor space. Follow this step-by-step guide to install your heater properly, using Xpro Gripaloc to seal the threads for a secure connection.

Materials Needed

  • Kickspace heater unit
  • Drill and drill bits
  • Measuring tape
  • Piping (for plumbing, if applicable)
  • Electrical wiring tools
  • Wire nuts or connectors
  • Wall thermostat (if required)
  • Xpro Gripaloc (thread sealant)
  • Wrenches
  • Screws and mounting hardware (usually provided with the heater)

Step 1: Prepare the Installation Area

  1. Choose the Location: Locate the kickspace under a cabinet where the heater will be installed. Make sure there’s access to electrical and/or plumbing connections.
  2. Measure and Mark: Measure the size of the heater and mark the cutout area on the base of the cabinet.
  3. Cut the Opening: Use a jigsaw or reciprocating saw to cut the marked area for the heater to fit snugly.

Step 2: Connect Plumbing (for Hydronic Heaters)

  1. Turn Off Water Supply: Before starting, turn off the water supply and drain the system.
  2. Install the Pipes: Position the heater’s inlet and outlet connections for easy access. Connect the pipes from your home’s heating system to the heater.
  3. Seal the Threads: Apply Xpro Gripaloc thread sealant to the pipe threads. Ensure even coverage for a watertight seal. Tighten the connections using a wrench but avoid over-tightening, which can damage the threads.
  4. Test for Leaks: Turn the water back on and check for leaks at the connections.

Step 3: Electrical Wiring

  1. Turn Off Power: Shut off the power at the circuit breaker before handling any electrical connections.
  2. Wire the Heater: Connect the heater to the electrical system according to the manufacturer’s instructions. These are usually on plugs, so learn how to wire a plug socket up first!
  3. Install a Thermostat: If your heater requires a thermostat, connect it to the appropriate wiring. Most have an internal thermostat.
  4. Secure the Connections: Use wire nuts and ensure the connections are tight and secure.

Step 4: Mount the Heater

  1. Position the Heater: Slide the heater into the prepared opening under the cabinet.
  2. Secure the Unit: Use screws and mounting hardware to attach the heater to the cabinet base securely.
  3. Check Alignment: Ensure the heater is level and properly aligned for optimal performance.

Step 5: Test the Heater

  1. Turn on Power and Water: Restore power and water supply.
  2. Check Functionality: Turn on the heater and test its heating capabilities. Ensure the fan and thermostat are functioning correctly.
  3. Inspect for Leaks and Noise: Double-check all connections for leaks and listen for unusual noises.

Maintenance Tips

  • Regularly clean the heater grille to remove dust and debris. If there’s a filter, clean this too.
  • Inspect connections periodically to ensure there are no leaks or loose wires.
  • Test the heater before the cold season to ensure it’s ready to use.

By using Xpro Gripaloc, you’ve added an extra layer of security to your connections, ensuring that your kickspace heater operates efficiently and without leaks. Enjoy your warm and cozy kitchen!

Not the best thing to happen to a dear old lady at 3am.. Chris Cannon called out to a flooded bathroom because of this #FlexiFriday
Send your pics/video & tag @plumberparts with #PlumbingDisaster 
-
-
-�
#Plumbing #Plumber #Apprentice #apprenticeship #Tradesman #Trade #OnTheTools #SiteBanter #DIY #DoItYourself #Pipework  #worldplumbers #PipePerfect #PlumberLife #hvaclife #plombier #Plomoro #Plomberie #FindYourPlumber
Check out what @alanwallace572 found. Back in the day when plumbing materials were made to last... Ceramic syphon that never skipped a beat. Send your pics/video & tag @plumberparts with #PlumbProud 💖✌ 
-
-
-�
#Plumbing #Plumber #Apprentice #apprenticeship #Tradesman #Trade #OnTheTools #SiteBanter #DIY #DoItYourself #Pipework #worldplumbers #PipePerfect #PlumberLife #hvaclife #plombier #Plomoro #Plomberie #FindYourPlumber
The Christmas rush..... LOCKED IN.
Love this install by @wadsleyplumbtech with a instantaneous water heater. Great job mate keeping it neat and tidy. Send your pics/video & tag @plumberparts with #PlumbProud 💖✌ 
-
-
-�
#Plumbing #Plumber #Apprentice #apprenticeship #Tradesman #Trade #OnTheTools #SiteBanter #DIY #DoItYourself #Pipework #worldplumbers #PipePerfect #PlumberLife #hvaclife #plombier #Plomoro #Plomberie #FindYourPlumber
This error message is only visible to WordPress admins
Error: Access Token is not valid or has expired. Feed will not update.